Charge Controller EPSolar MPPT Triron Series 10-40A
Highly efficient and compact MPPT charge controller for self configuration!
- Selection of 3 different display modules
- Selection of 3 different port modules
- System voltage: 12-24V
- MPPT voltage range: up to 72V
- Max. charging current: 10-40A
- PV power: from 130W up to 1040W
- Max. PV open circuit voltage (Voc): 60-100V
Features
- Free selection from various display and port modules
- Automatic recognition of the selected modules
- Advanced MPPT algorithm to minimize losses
- DC-DC conversion efficiency of 98%
- Wide MPP voltage range
- Compatible with lead-acid and lithium batteries
- Including required temperature compensation
- Real time display of energy statistics
- Automatic power reduction in case of overheating
- LCD display and LED to indicate operating data and operating modes
- Easy operation with integrated buttons
- Master and slave RS485 communication to read the operating data of the load or Inverter
- Control of the inverter switch via the relay interface
- Provides 5VDC via dual USB output interface for charging electronic devices
Technical Data
- System voltage: 12-24V
- MPPT voltage range: up to 72V
- Max. charging current: 10-40A
- PV power: from 130W up to 1040W
- Max. PV open circuit voltage (Voc): 60-100V
- Operating temperature: -25°C to +50°C
- Protection class: IP30
- Grounding: Negative
The XTRA-N series can display different display units (XDB1 / XDS1 / XDS2).
The series includes a water-repellent housing (design) with protection class IP32.
With the new XTRA-N series, the reliability of the devices has been significantly improved, so they meet a wide range of application requirements.
 |
| BUY NOW |
 |
| BUY NOW |
MPPT (Max Power Point Tracking) makes optimal use of the full power of your solar modules.
For all common module technologies, optimal for solar systems with module voltages that are higher than the battery voltage. With these controllers you can also use modules that are actually intended for use in grid-connected systems.
The most efficient working point of the solar modules changes due to various factors, such as module temperature, irradiation, module type etc. This working point is constantly monitored by the internal microcontroller and, if necessary, controlled in such a way that the optimal performance of the solar module is given and your batteries are charged with the respective greatest current .
Properties
- advanced MPPT technology
- high efficiency of not less than 98%
- \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\“ultra-fast\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\“ recording speed
- precise detection of several maximum power points (MPP)
- multifunctional LCD display
- manual adjustment of the battery types, load control etc.
- negative grounding via (-) pole
- RS485 interface with MODBUS industry standard
- Fully programmable functions via PC software
- automatic limitation of charging power and current
- large MPP operating voltage range
- compatible with lead-acid and lithium-ion batteries
- Battery temperature compensation function
- Real-time energy statistics
- Overheat reduction function
- several working modes for loading
Tracer AN Series MPPT Solar Charge Controller
Very large range of application from caravans, single family houses to large installations.
- MPPT charge controller 60A/80A/100A
- 12-48V system voltage
- MPP voltage range up to 108V/144V
- Negative grounding
- Compatible with Lithium batteries
Simple design of larger hybrid systems
- Up to 8 charge controllers in parallel operation
- Integration of grid/generator chargers
The advanced MPPT algorithm reduces the number of lost MPPs (points of maximum power) as well as the time lost for correction. Due to the increased tracking efficiency and speed, the MPP is adjusted very quickly to take the highest possible power from the PV modules at any time.
The limiting function of charging power and current, as well as the automatic power reduction protects the system in case of excessive PV power or increased temperatures.
The adaptable 3-stage charging curve, based on a digital control loop, enables maximum battery life and an increase in system performance. With the load relay and the grid/generator control relays, a hybrid energy system can be easily set up. Comprehensive electronic protection against overcharging, deep discharge, PV polarity reversal, etc. ensures a safe and stable solar system.
The isolated RS-485 interface with standard Modbus protocol and 5V power supply makes a system expansion easy. It supports up to 8 charge controllers in parallel operation. This results in a very wide range of applications from caravans to single-family homes and large installations.
Inverter / charge controller UPower series from EPSolar for PV / solar applications. Suitable for solar, car, boat, camping, outdoor, caravan, motorhome etc. Ideal for use in remote areas with many hours of sunshine and with a lack of reliable suppliers.
The function of the integrated MPPT charge controller ensures fully digital and efficient energy storage and use. The inverter with integrated charge controller of the UPower series converts 12 / 48V direct current into 220 / 230V 50 / 60Hz alternating current with pure sine wave. The manual adjustment of the utility and PV electricity charges enables the ideal ratio of your energy use. This makes the UPower particularly convincing in remote environments with its reliability and responsiveness.
Characteristics
- Charge controller and inverter in one device
- High stability in the output voltage
- Selection function for the ratio of utility and solar power
- MPPT technology for determining the maximum credit point
- Numerous protective functions: over / under voltage of the battery, over / under voltage at inputs and outputs, protection against reverse polarity and short circuits
- Charging power limits
- Compensation function for temperature changes
- Protection against internal overheating with intelligent ventilation
- Sophisticated SPWM technology for the pure output of sine waves
- low distortion factor (= THD = 3%)
- 4.2 \\\\\\\\\\\\\\\\“display for showing the system status and real-time data
- Easy adjustment of the working parameters with 4 buttons
- Optional: Wi-Fi module for wireless monitoring and control
- Control using PC software or APP
Technical specifications
- Nominal battery voltage: 12V or 48V
- Continuous power: 800W / 4000W
- Maximum power: 2000W / 10000W (short-term peak)
Charge controller EPSolar MPPT DuoRacer 10-30A
Highly efficient, compact and reliable charge controller to use the full power of your solar modules
The MPPT charge controller DuoRacer from EPSolar was specially designed to charge two batteries in a solar system at the same time. Several battery types (Sealed, Gel, Flooded, LiFePO4 and Li-NiCoMn) are supported.
- MPPT Charge Controller 10A-30A
- 12-24V system voltage
- MPP voltage range up to 72V
- Negative grounding
The MPPT solar charge controller Duo Racer from EPSolar charges two batteries (BATT1 and BATT2) at the same time and is therefore ideally suited for traveling in RV, caravan or car. With the AES interface, the DuoRacer is able to supply excess PV energy to consumers such as a refrigerator.
BATT1 = Battery storage to supply consumers in an island system, household (supports Sealed, Gel, Flooded, LiFePO4, Li-NiCoMn)
BATT2 = Battery storage for vehicles, boats (supports only lead acid batteries)
Features
- MPPT technology with efficiency =99.5%.
- Well-developed MPPT control algorithm to minimize MPP loss rate
- automatic limitation of charging power and charging current
- LCD display – display and setting of parameters
- RS485 port, Modbus protocol
- Compatible with LiFePo4 and Li-NiCoMn batteries
- Automatic energy saving mode when charging power is too low
- Wide MPP operating voltage range
- Numerous protection mechanisms (deep discharge, overcharge, overvoltage protection)
- AES port for max. utilization of the PV surplus
Optional
The monitoring and evaluation of the data can be realised by using the PC software. The controller must either be connected directly to the PC via RS485 cable or via WLAN/Bluetooth with the e-box-WiFi / e-box-BLE.
A converter is required to connect consumers with 12V via the AES port.
Charge Controller EPsolar MPPT Tracer BN-Series 10-40A 12-24V
Characteristics
- MPPT (Max Power Point Tracking)
- Maximum charge current 10-40A
- Automatic system voltage detection 12/24V
- Solar input module open circuit voltage from 5V to 150V open circuit voltage
- battery deep discharge protection, overcharge protection, overvoltage protection
- RS485/ interface, Modbus protocol
- Monitoring via PC software or display MT50
- Temperature dependent charging parameter correction
- Fanless convection cooling up to 50°C
- Timer function up to 1-15 hours Option for night lighting
- Automatic day/night detection
- Load output with switch-off option
- 4 battery types adjustable ( open acid, AGM, gel, user)
- suitable for lithium batteries
Technical data
- Battery Nominal voltage 12/24 DC
- Module open circuit voltage up to 150V DC
- Max. charging current 10A – 40A
- Type. Own current consumption < 50 mA
- Temperature range – 25°C to + 60°C
- Protection class IP20
Features
The controller can be monitored and adjusted with the MT50 display or adapter cable and software. The controller can be monitored via the PC software.
There are 4 battery types adjustable. In the battery type user the voltages are freely selectable and programmable via the software. (lithium batteries)
A switchable load output enables the user to switch on or off all loads connected to the solar charge controller with one keystroke on the controller or via software settings on the PC.
2 timers can control a night lighting as soon as the controller detects \“night\“ by the solar module.
Yield measurement of all system parameters and monitoring via PC software possible.
With the optionally available display MT50 the controller can be adjusted and monitored.
The charge controllers of the iTracer series are industrial goods with an extended Maximum Power Point Tracking (MPPT) algorithm. You can supply the maximum available power for charging batteries.
Properties
- MPPT (Max Power Point Tracking)
- Maximum charging current 60 amps
- Automatic system voltage detection 12/24/36 / 48V
- Solar input module open circuit voltage from 5V to 145V open circuit voltage
- Battery deep discharge protection, overcharge protection, overvoltage protection
- RS485 / Can-bus interfaces available
- Monitoring via PC software
- Temperature-dependent charging parameter correction
- Fanless convection cooling up to 50 ° C
- Timer function up to 1-15 hours option for night lighting
- Automatic day / night detection
- Load output with switch-off option
- 4 battery types adjustable (open acid, AGM, gel, user)
Technical specifications
- Battery nominal voltage 12/24/36/48 DC
- Module open circuit voltage up to 145V DC
- Max. Module power 720W (12V) / 1440W (24V) / 2160W (36V) / 2880W (48V)
- Max. Charging current 60 A
- Type. Own power consumption <1.5 W
- Temperature range – 25 ° C to + 60 ° C
- Degree of protection IP20
- Dimensions in mm 440 x 231 x 110
- Weight 5.9 kg
- Connection terminals 35 mm²
Features
The controller can be monitored and set using the software supplied. The controller can be monitored using the PC software.
4 types of batteries can be set. In the user battery type, the voltages are freely selectable and programmable via the software. (Lithium batteries)
A switchable load output gives the user the option of switching on or off all consumers that are connected to the solar charge controller by pressing a button on the controller or via software settings on the PC.
2 timers can control night lighting as soon as the controller detects \\“night\\“ through the solar module.
Yield measurement of all system parameters and monitoring via PC software possible.
Charge Controller EPSolar MPPT Tracer AN Series 10-40A
Characteristics
- MSRT (Multiphase synchronous rectifier technology)
- Advanced MPPT logarithms with dual-core processor Architecture
- High reliability and high industry quality standards
- High conversion efficiencies for improved solar system energy efficiency
- The limiting function of charge power and current
- Temperature compensation function
- Automatic power reduction protects the system in case of excessive PV power or temperatures.
- 3-step charge curve allows maximum battery life
- Electronic protection: overcharge, deep discharge, PV polarity reversal, etc.
- Insulated RS-485 interface with standard Modbus protocol and 5V power supply
- Compatible with lithium-ion batteries
- Real time monitoring and parameter setting via smart phone or PC APP
Technical data
- System voltage: 12-24V
- MPPT voltage range: up to 72V
- Max. charging current: 10-40A
- Max. power: from 130W up to 1040W
- Max. PV open circuit voltage (Voc): 100V
- Operating temperature: -25°C to +50°C
- Protection class: IP30
- Grounding: Negative
Features
The controller can be monitored and adjusted with the MT50 display or adapter cable and software. The controller can be monitored via the PC software.
There are 4 battery types adjustable. In the battery type user the voltages are freely selectable and programmable via the software. (lithium batteries)
A switchable load output enables the user to switch on or off all loads connected to the solar charge controller with one keystroke on the controller or via software settings on the PC.
2 timers can control a night lighting as soon as the controller detects “night“ by the solar module.
Yield measurement of all system parameters and monitoring via PC software possible.
With the optionally available display MT50 the controller can be adjusted and monitored.