Skip to content
2
Yes
None
1
1000
/products/
Thumbnail

Categories:

Sub-Categories:

Charge Controller
Triron Series (10-40A)

Charge Controller EPSolar MPPT Triron Series 10-40A

Highly efficient and compact MPPT charge controller for self configuration!

  • Selection of 3 different display modules
  • Selection of 3 different port modules
  • System voltage: 12-24V
  • MPPT voltage range: up to 72V
  • Max. charging current: 10-40A
  • PV power: from 130W up to 1040W
  • Max. PV open circuit voltage (Voc): 60-100V

Features

  • Free selection from various display and port modules
  • Automatic recognition of the selected modules
  • Advanced MPPT algorithm to minimize losses
  • DC-DC conversion efficiency of 98%
  • Wide MPP voltage range
  • Compatible with lead-acid and lithium batteries
  • Including required temperature compensation
  • Real time display of energy statistics
  • Automatic power reduction in case of overheating
  • LCD display and LED to indicate operating data and operating modes
  • Easy operation with integrated buttons
  • Master and slave RS485 communication to read the operating data of the load or Inverter
  • Control of the inverter switch via the relay interface
  • Provides 5VDC via dual USB output interface for charging electronic devices

Technical Data

  • System voltage: 12-24V
  • MPPT voltage range: up to 72V
  • Max. charging current: 10-40A
  • PV power: from 130W up to 1040W
  • Max. PV open circuit voltage (Voc): 60-100V
  • Operating temperature: -25°C to +50°C
  • Protection class: IP30
  • Grounding: Negative

Datasheet-German

Datasheet-English

Manual-German

Manual-English

BUY NOW

XTRA Series

The XTRA-N series can display different display units (XDB1 / XDS1 / XDS2).
The series includes a water-repellent housing (design) with protection class IP32.

With the new XTRA-N series, the reliability of the devices has been significantly improved, so they meet a wide range of application requirements.

MPPT XTRA 12-24V
            BUY NOW
MPPT XTRA 12-48V
            BUY NOW

 

MPPT (Max Power Point Tracking) makes optimal use of the full power of your solar modules.

For all common module technologies, optimal for solar systems with module voltages that are higher than the battery voltage. With these controllers you can also use modules that are actually intended for use in grid-connected systems.

The most efficient working point of the solar modules changes due to various factors, such as module temperature, irradiation, module type etc. This working point is constantly monitored by the internal microcontroller and, if necessary, controlled in such a way that the optimal performance of the solar module is given and your batteries are charged with the respective greatest current .

Properties

  • advanced MPPT technology
  • high efficiency of not less than 98%
  • \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\“ultra-fast\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\“ recording speed
  • precise detection of several maximum power points (MPP)
  • multifunctional LCD display
  • manual adjustment of the battery types, load control etc.
  • negative grounding via (-) pole
  • RS485 interface with MODBUS industry standard
  • Fully programmable functions via PC software
  • automatic limitation of charging power and current
  • large MPP operating voltage range
  • compatible with lead-acid and lithium-ion batteries
  • Battery temperature compensation function
  • Real-time energy statistics
  • Overheat reduction function
  • several working modes for loading

Datasheet English

Datasheet German

Manual English

Manual German

GoMate Series

The GoMate series combines design with technology and is an eye-catcher among solar charge controllers.

The fully integrable solar charge controllers were specially developed for an aesthetically unobtrusive installation. They work with an efficient PWM charging mode and are equipped with a special LCD display that shows the real-time data of the system.

All operating states can be read easily and quickly on the display. The charge controller works completely automatically and is easy to use.

The GoMate regulates the PV current and protects your battery against overcharging. The device is compatible with 12-24 volt photovoltaic systems and can be used with any off-grid solar system, e.g. in mobile homes, garden houses, boats or vehicles.

Properties

  • Fully integrable device in a modern design
  • High quality and fail-safe components for a long product life
  • Intelligent 3-stage charging curve: bulk, boost / equalize and float
  • Battery types: Sealed, Gel, Flooded and User (AGM, Gel, Liquid and User)
  • Real time energy statistics
  • Battery temperature compensation function
  • Digital LCD monitor for an informative display of operating parameters and error messages
  • Connection for voltage drop and temperature compensation
  • RS-485 interface with Modbus protocol and short-circuit protection for 5V / 200mA applications
  • Different communication options
  • Nominal charging power at operating temperature without reduction
  • Comprehensive electronic protection
  • Display and setting of the parameters via PC software or app

Datasheet English

Datasheet German

Manual English

Manual German

BUY NOW

Tracer AN Series (50-100A)

Tracer AN Series MPPT Solar Charge Controller

Very large range of application from caravans, single family houses to large installations.

  • MPPT charge controller 60A/80A/100A
  • 12-48V system voltage
  • MPP voltage range up to 108V/144V
  • Negative grounding
  • Compatible with Lithium batteries

Simple design of larger hybrid systems

  • Up to 8 charge controllers in parallel operation
  • Integration of grid/generator chargers

 

The advanced MPPT algorithm reduces the number of lost MPPs (points of maximum power) as well as the time lost for correction. Due to the increased tracking efficiency and speed, the MPP is adjusted very quickly to take the highest possible power from the PV modules at any time.

The limiting function of charging power and current, as well as the automatic power reduction protects the system in case of excessive PV power or increased temperatures.

The adaptable 3-stage charging curve, based on a digital control loop, enables maximum battery life and an increase in system performance. With the load relay and the grid/generator control relays, a hybrid energy system can be easily set up. Comprehensive electronic protection against overcharging, deep discharge, PV polarity reversal, etc. ensures a safe and stable solar system.

The isolated RS-485 interface with standard Modbus protocol and 5V power supply makes a system expansion easy. It supports up to 8 charge controllers in parallel operation.  This results in a very wide range of applications from caravans to single-family homes and large installations.

Datasheet English

Datasheet German

Manual English

Manual German

BUY NOW

UPower Series

Inverter / charge controller UPower series from EPSolar for PV / solar applications. Suitable for solar, car, boat, camping, outdoor, caravan, motorhome etc. Ideal for use in remote areas with many hours of sunshine and with a lack of reliable suppliers.

The function of the integrated MPPT charge controller ensures fully digital and efficient energy storage and use. The inverter with integrated charge controller of the UPower series converts 12 / 48V direct current into 220 / 230V 50 / 60Hz alternating current with pure sine wave. The manual adjustment of the utility and PV electricity charges enables the ideal ratio of your energy use. This makes the UPower particularly convincing in remote environments with its reliability and responsiveness.

Characteristics

  • Charge controller and inverter in one device
  • High stability in the output voltage
  • Selection function for the ratio of utility and solar power
  • MPPT technology for determining the maximum credit point
  • Numerous protective functions: over / under voltage of the battery, over / under voltage at inputs and outputs, protection against reverse polarity and short circuits
  • Charging power limits
  • Compensation function for temperature changes
  • Protection against internal overheating with intelligent ventilation
  • Sophisticated SPWM technology for the pure output of sine waves
  • low distortion factor (= THD = 3%)
  • 4.2 \\\\\\\\\\\\\\\\“display for showing the system status and real-time data
  • Easy adjustment of the working parameters with 4 buttons
  • Optional: Wi-Fi module for wireless monitoring and control
  • Control using PC software or APP

Technical specifications

  • Nominal battery voltage: 12V or 48V
  • Continuous power: 800W / 4000W
  • Maximum power: 2000W / 10000W (short-term peak)

Datasheet English

Datasheet German

Manual English

Manual German

BUY NOW

DuoRacer Series(10-30A)

Charge controller EPSolar MPPT DuoRacer 10-30A

Highly efficient, compact and reliable charge controller to use the full power of your solar modules

The MPPT charge controller DuoRacer from EPSolar was specially designed to charge two batteries in a solar system at the same time. Several battery types (Sealed, Gel, Flooded, LiFePO4 and Li-NiCoMn) are supported.

  • MPPT Charge Controller 10A-30A
  • 12-24V system voltage
  • MPP voltage range up to 72V
  • Negative grounding

The MPPT solar charge controller Duo Racer from EPSolar charges two batteries (BATT1 and BATT2) at the same time and is therefore ideally suited for traveling in RV, caravan or car. With the AES interface, the DuoRacer is able to supply excess PV energy to consumers such as a refrigerator.

BATT1 = Battery storage to supply consumers in an island system, household (supports Sealed, Gel, Flooded, LiFePO4, Li-NiCoMn)
BATT2 = Battery storage for vehicles, boats (supports only lead acid batteries)

Features

  • MPPT technology with efficiency =99.5%.
  • Well-developed MPPT control algorithm to minimize MPP loss rate
  • automatic limitation of charging power and charging current
  • LCD display – display and setting of parameters
  • RS485 port, Modbus protocol
  • Compatible with LiFePo4 and Li-NiCoMn batteries
  • Automatic energy saving mode when charging power is too low
  • Wide MPP operating voltage range
  • Numerous protection mechanisms (deep discharge, overcharge, overvoltage protection)
  • AES port for max. utilization of the PV surplus

Optional

The monitoring and evaluation of the data can be realised by using the PC software. The controller must either be connected directly to the PC via RS485 cable or via WLAN/Bluetooth with the e-box-WiFi / e-box-BLE.

A converter is required to connect consumers with 12V via the AES port.

Datasheet English

Datasheet German

Manual English

Manual English

PRODUKT JETZT KAUFEN

Tracer BN Series (10-40A)

Charge Controller EPsolar MPPT Tracer BN-Series 10-40A 12-24V

Characteristics

  • MPPT (Max Power Point Tracking)
  • Maximum charge current 10-40A
  • Automatic system voltage detection 12/24V
  • Solar input module open circuit voltage from 5V to 150V open circuit voltage
  • battery deep discharge protection, overcharge protection, overvoltage protection
  • RS485/ interface, Modbus protocol
  • Monitoring via PC software or display MT50
  • Temperature dependent charging parameter correction
  • Fanless convection cooling up to 50°C
  • Timer function up to 1-15 hours Option for night lighting
  • Automatic day/night detection
  • Load output with switch-off option
  • 4 battery types adjustable ( open acid, AGM, gel, user)
  • suitable for lithium batteries

Technical data

  • Battery Nominal voltage 12/24 DC
  • Module open circuit voltage up to 150V DC
  • Max. charging current 10A – 40A
  • Type. Own current consumption < 50 mA
  • Temperature range – 25°C to + 60°C
  • Protection class IP20

Features

The controller can be monitored and adjusted with the MT50 display or adapter cable and software. The controller can be monitored via the PC software.
There are 4 battery types adjustable. In the battery type user the voltages are freely selectable and programmable via the software. (lithium batteries)
A switchable load output enables the user to switch on or off all loads connected to the solar charge controller with one keystroke on the controller or via software settings on the PC.
2 timers can control a night lighting as soon as the controller detects \“night\“ by the solar module.
Yield measurement of all system parameters and monitoring via PC software possible.
With the optionally available display MT50 the controller can be adjusted and monitored.

Datasheet English

Manual English

Manual German

BUY NOW

iTracer Series

The charge controllers of the iTracer series are industrial goods with an extended Maximum Power Point Tracking (MPPT) algorithm. You can supply the maximum available power for charging batteries.

Properties

  • MPPT (Max Power Point Tracking)
  • Maximum charging current 60 amps
  • Automatic system voltage detection 12/24/36 / 48V
  • Solar input module open circuit voltage from 5V to 145V open circuit voltage
  • Battery deep discharge protection, overcharge protection, overvoltage protection
  • RS485 / Can-bus interfaces available
  • Monitoring via PC software
  • Temperature-dependent charging parameter correction
  • Fanless convection cooling up to 50 ° C
  • Timer function up to 1-15 hours option for night lighting
  • Automatic day / night detection
  • Load output with switch-off option
  • 4 battery types adjustable (open acid, AGM, gel, user)

Technical specifications

  • Battery nominal voltage 12/24/36/48 DC
  • Module open circuit voltage up to 145V DC
  • Max. Module power 720W (12V) / 1440W (24V) / 2160W (36V) / 2880W (48V)
  • Max. Charging current 60 A
  • Type. Own power consumption <1.5 W
  • Temperature range – 25 ° C to + 60 ° C
  • Degree of protection IP20
  • Dimensions in mm 440 x 231 x 110
  • Weight 5.9 kg
  • Connection terminals 35 mm²

Features

The controller can be monitored and set using the software supplied. The controller can be monitored using the PC software.
4 types of batteries can be set. In the user battery type, the voltages are freely selectable and programmable via the software. (Lithium batteries)
A switchable load output gives the user the option of switching on or off all consumers that are connected to the solar charge controller by pressing a button on the controller or via software settings on the PC.
2 timers can control night lighting as soon as the controller detects \\“night\\“ through the solar module.
Yield measurement of all system parameters and monitoring via PC software possible.

Datasheet English

Manual English

Manual German

BUY NOW

VS AU Series

The VS series is a generation of charge controllers for off-grid solar systems, such as street lighting, solar home systems or small power plants, etc. It combines an LCD display, reliable battery charging, fully electronic protection, programmable parameters as well as other features and powerful functions.

Advantages

  • Intelligent 3-level PWM charge detection: bulk, boost / equalize, float
  • 3 supported battery options: Sealed, Gel, and Flooded
  • LCD display
  • Multiple types of load control
    Battery temperature compensation
    Comprehensive electronic protection devices

Available in:

  • 30/45/60 A for 12/24/36 / 48V system voltage
  • 10/20/30/45/60 A for 12 / 24V system voltage

Properties

  • Keeps the battery fully charged
  • Can be used for acid, AGM, gel
  • Reverse polarity protection for battery and solar panel
  • External battery temperature sensor can be connected
  • Prevents damage to the battery
  • Automatic shutdown if the charging current exceeds the capacity of the controller
  • Timer function option for night lighting
  • LCD display
  • PWM modulation
  • 2 USB ports

Application

  • Solar lighting system
  • Solar home system
  • Solar monitoring
  • Caravan and boats
  • Solar road traffic signals
  • Solar power plant

Technical specifications

PWM charge controller 10/20/30/45/60 A

  • System voltage 12 / 24V
  • Open circuit voltage up to 50V
  • Positive grounding

PWM charge controller 30/45/60 A

  • System voltage 12/24/36 / 48V
  • Open circuit voltage up to 96V
  • Positive grounding

Datasheet English

Datasheet German 12-24V

Datasheet German 12-48V

Manual English

BUY 12-24V NOW

BUY 12-48V NOW

VS BN Series

The devices of the VS BN series can charge and discharge a battery automatically, especially with off-grid PV systems.

The current operating state is determined by a hybrid actuator and, as a result, the charging process is optimized by the principle of pulse width modulation. Therefore, PWM charge controllers are significantly more effective than simple linear charge controllers.
The built-in microprocessor gently charges the battery, thereby guaranteeing a long lifespan for your solar batteries.

The charge status and the charging via the solar module can be seen from the LEDs. The built-in undervoltage protection prevents the battery from over-discharging. Overcharging of the batteries is thus prevented since the charge controller ends the charging process when the full capacity is reached.

Properties

  • Keeps the battery fully charged
  • Can be used for acid, AGM, gel and lithium batteries
  • Prevents the battery from supplying voltage to the solar system at night
  • Reverse polarity protection for battery and solar panel
  • External battery temperature sensor can be connected
  • RS485 / interface with Modbus protocol available
  • Automatic shutdown if the charging current exceeds the capacity of the controller
  • Automatic temperature compensation (ATC)
  • Timer function up to 1-15 hours option for night lighting
  • LED shows the charge status of the battery
  • LCD display with 4 buttons selection and menu
  • PWM modulation
  • Automatic switching on / off of the charging current, depending on the battery charge
  • 4 battery types adjustable (open acid, AGM, gel, user)
  • Suitable for lithium batteries

Application

  • Solar home system
  • Traffic signals
  • Solar lighting
  • Video surveillance

Technical specifications

PWM charge controller 10/20/30/45 A

  • System voltage 12 / 24V
  • Open circuit voltage up to 50V
  • Negative grounding

PWM charge controller 45/60 A

  • System voltage 12/24/36 / 48V
  • Open circuit voltage up to 96V
  • Negative grounding

Datasheet English

Datasheet German 12-24V

Datasheet German 12-48V

Manual English

Manual German

BUY 12-24V NOW

BUY 12-48V NOW

EP Series

The EP series is a double battery charging control for caravans, campers, boats and golf carts etc. The charging priority can be selected.

Solar charge controller with system voltages from 12V to 24Volt for 2 different batteries with up to 320/640 Watt module output at 12V / 24Volt battery voltage.

The charge controller is connected between the solar module and the consumer battery and vehicle battery and controls the charging process so that the batteries are always charged to the maximum. It can charge one battery as well as two different batteries with different priorities.
The built-in microprocessor gently charges the battery, thereby guaranteeing a long lifespan for your solar batteries.

The charge status and the charging via the solar module can be seen from the LEDs.
Overcharging of the batteries is prevented since the charge controller ends the charging process when the full capacity is reached.
The integrated microprocessor controls the switching thresholds of the charging process precisely and temperature stable.

Product characteristics

  • RJ45 interface for remote display for optional external display MT1
  • Yield measurement with optional display
  • PWM charging with temperature compensation
  • LED display for charging and battery charge status
  • Keeps the battery fully charged
  • Prevents the battery from supplying voltage to the solar system at night
  • Reverse polarity protection for battery AND solar panel
  • Automatic temperature compensation (ATC)
  • LED shows the charge status of the battery
  • Automatic switching on / off of the charging current, depending on the battery charge
  • 3 battery types adjustable (acid, AGM, gel)

Technical specifications

  • System voltage: 12V, 24V (automatic detection)
  • Nominal PV power: 160 / 320W (12V) 320 / 640W (24V)
  • Maximum charging current: 10-20A
  • DC input voltage (modular working voltage) max. 27V with 12V battery and 37V with 24V battery
  • Leakage current with no charge: = <4mA
  • Temperature compensation: -30mv / ° C / 2V
  • Temperature range: -35 ° C to + 55 ° C
  • Dimensions: 153 x 76 x 37 mm
  • Weight: 100 g
  • Protection class IP20 (dry room)
  • Connection terminals for max. Cable cross section 6mm²

Manual English

Manual German

BUY NOW

Tracer AN Series (10-40A)

Charge Controller EPSolar MPPT Tracer AN Series 10-40A

Characteristics

  • MSRT (Multiphase synchronous rectifier technology)
  • Advanced MPPT logarithms with dual-core processor Architecture
  • High reliability and high industry quality standards
  • High conversion efficiencies for improved solar system energy efficiency
  • The limiting function of charge power and current
  • Temperature compensation function
  • Automatic power reduction protects the system in case of excessive PV power or temperatures.
  • 3-step charge curve allows maximum battery life
  • Electronic protection: overcharge, deep discharge, PV polarity reversal, etc.
  • Insulated RS-485 interface with standard Modbus protocol and 5V power supply
  • Compatible with lithium-ion batteries
  • Real time monitoring and parameter setting via smart phone or PC APP

Technical data

  • System voltage: 12-24V
  • MPPT voltage range: up to 72V
  • Max. charging current: 10-40A
  • Max. power: from 130W up to 1040W
  • Max. PV open circuit voltage (Voc): 100V
  • Operating temperature: -25°C to +50°C
  • Protection class: IP30
  • Grounding: Negative

Features

The controller can be monitored and adjusted with the MT50 display or adapter cable and software. The controller can be monitored via the PC software.
There are 4 battery types adjustable. In the battery type user the voltages are freely selectable and programmable via the software. (lithium batteries)
A switchable load output enables the user to switch on or off all loads connected to the solar charge controller with one keystroke on the controller or via software settings on the PC.
2 timers can control a night lighting as soon as the controller detects “night“ by the solar module.
Yield measurement of all system parameters and monitoring via PC software possible.
With the optionally available display MT50 the controller can be adjusted and monitored.

Datasheet-German

Datasheet-English

Manual-German

Manual-English

BUY NOW

LS1024EPD 12-24V 10A

Charge Controller EPSolar PWM LS1024EPD 10A 12/24V

  • 12/24 VDC
  • Day / Night recognition
  • LED Indicator for battery status
  • Electronic protection
  • Intelligent timer function (1-13h)
  • IP67 protection
  • PWM charging method to increase battery lifetime
  • 3-step intelligent PWM-Charging: Bulk, Boost / Equalize, Float

Charge controller EPSolar PWM LS1024EPD 10A 12/24V

Characteristics

  • One button for all Settings
  • Electronic protection functions:
    • Overcharging
    • Over discharging
    • Overload
    • Short circuit
    • Reverse polarity of the PV modules
  • Suitable for industry, many application possibilities
  • PWM charging function for maximum performance

Technical data

  • Nominal voltage: 12/24 V automatic detection
  • Max. PV Input voltage: 50V
  • Charging current: 10A
  • Battery types adjustable: Sealed (factory setting), Gel, Flooded
  • Dimensions: 108.5 x 75 x 25.6 mm
  • Weight: 0,41 kg
  • Protection class: IP67
  • Working temperature range: -35°C to + 55°C
  • Timer function

Datasheet english

Datasheet german

Manual english

LS EU Series

 Charge controller EPSolar PWM LS-EU Series

 

The LS-EU solar charge controller is a new member of the LandStar family and is ideal for small solar installations, especially household systems.

The LS-EU series also has a + 5V / 1.2 A USB port to charge e.g. mobile phones, fans and other electronic devices.

Features

  • Highly efficient PWM charging technology to increase battery life and improve solar yield
  • Using MOSFET as an electronic switch, without mechanical switches or relays
  • Intuitive LED indicators for battery voltage status
  • 3 different battery types adjustable Gel, AGM or open lead acid battery
  • Manual control of the consumer output possible
  • Temperature compensation for optimal charging and discharging of the battery
  • User-friendly, comfortable and easy to adjust

Electronic protection functions

  • Overload protection
  • Short circuit protection
  • Battery deep discharge protection
  • Battery reverse polarity protection

BUY NOW

Inverter
IPower Plus Series

Sine wave inverter EPSolar IPower Plus series 1500-3000W 12-48V

For use in solar applications, car, boat, camping, outdoor, caravan, motorhome etc.

 

  • Nominal voltage battery: 12V / 24V / 48V
  • Continuous output power: 1500W – 3000W
  • Maximum power: 3000W – 6000W (short-term peak)
  • compatible with lithium batteries
  • compatible with display/remote control and eBox – Wifi/BLE

 

The IPower Plus sine wave inverter fully digitally converts 12V/24V/48V DC to 220/230V 50/60Hz AC. High reliability, high efficiency, compact size, easy installation and operation characterize the IPower Plus series. The inverters can be used in a wide variety of appliances such as home appliances, power tools and industrial applications, and are especially suitable for photovoltaic systems.

Features

  • Input and output are completely isolated from each other
  • Advanced SPWM technology for pure sine wave Output
  • Suppression function surge currents for lithium BMS
  • Simple wiring and 180° rotatable LCD Display
  • Protection functions input: reverse polarity, undervoltage, overvoltage
  • Protective functions output: overload, short circuit, overheating
  • RS485 interface for display/remote control and eBox -Wifi/BLE
  • USB interface for direct power supply of small electrical consumers (not available for 48V models)
  • Monitoring of data and modification of parameters possible via PC software or smartphone APP (requires eBox)

Datasheet-German

DatasheetEnglish

Manual-English

BUY NOW

SHI Series

The SHI series sine wave inverters convert 12 / 24V direct current fully digital into 220 / 230V 50 / 60Hz alternating current. The SHI series is characterized by high reliability, high efficiency, compact size, easy installation and operation.

The inverters can be used for a wide variety of devices such as household appliances, electrical tools and industrial applications and are particularly suitable for photovoltaic systems.

Characteristics

  • Input and output are completely isolated from each other
  • Advanced SPWM technology for pure sine output
  • Dynamic performance control technology for reliable operation
  • Large DC input voltage range
  • Low harmonic distortion (THD = 3%)
  • LED display for input voltage, power output, function and error display
  • Switchable energy saving mode
  • Switchable output voltage and frequency
  • Comprehensive protection functions against short circuit, overload, undervoltage on the input side and overtemperature
  • Internal error detection
  • Wide operating temperature range (industrial level)
  • Continuous operation at full power

Technical specifications

  • Nominal battery voltage: 12V or 24V
  • Continuous power: 600W / 1000W / 2000W
  • Maximum power: 1350W / 2250W / 4600W (short-term peak)

Datasheet  English

Datasheet German

Manual English

BUY NOW

STI Series

The STI series sine wave inverters are fully digital and impress with their intelligent design. DC 12V / 24V / 48V to 220V AC / 50Hz, high performance DSP

Properties

  • high reliability
  • high efficiency
  • light weight
  • small volume
  • full protection functions
  • easy installation
  • easy operation

The inverter is used in many areas, especially for solar photovoltaic systems. It has been specially developed for many types of AC loads such as household appliances, power tools and industrial devices.

Technical Details

  • Nominal input voltage: 12 V / 24 V
  • Input voltage: 10.5 ~ 16VDC
  • No-load current: ≤5W
  • Output voltage: AC220V ± 3%
  • Nominal output: 200/300 VA
  • Max. Short-term power: 300/450 VA / 10 sec.
  • Output mode: single
  • Waveform: pure sine
  • Frequency: 50Hz ± 0.5%
  • Efficiency at nominal power: ≥81%
  • Temperature range: -25 ° C to + 50 ° C
  • Dimensions: 315 x 166 x 101 mm
  • Storage temperature: -35 ℃ ~ + 70 ℃
  • Operating height: <5000 m

Datasheet English

Manual English

Manual German

BUY NOW

Inverter Charger
UPower Series

Inverter / charge controller UPower series from EPSolar for PV / solar applications. Suitable for solar, car, boat, camping, outdoor, caravan, motorhome etc. Ideal for use in remote areas with many hours of sunshine and with a lack of reliable suppliers.

The function of the integrated MPPT charge controller ensures fully digital and efficient energy storage and use. The inverter with integrated charge controller of the UPower series converts 12/24V/48V direct current into 220 / 230V 50 / 60Hz alternating current with pure sine wave. The manual adjustment of the utility and PV electricity charges enables the ideal ratio of your energy use. This makes the UPower particularly convincing in remote environments with its reliability and responsiveness.

Characteristics

  • Charge controller and inverter in one device
  • High stability in the output voltage
  • Selection function for the ratio of utility and solar power
  • MPPT technology for determining the maximum credit point
  • Numerous protective functions: over / under voltage of the battery, over / under voltage at inputs and outputs, protection against reverse polarity and short circuits
  • Charging power limits
  • Compensation function for temperature changes
  • Protection against internal overheating with intelligent ventilation
  • Sophisticated SPWM technology for the pure output of sine waves
  • low distortion factor (= THD = 3%)
  • 4.2 \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\“display for showing the system status and real-time data
  • Easy adjustment of the working parameters with 4 buttons
  • Optional: Wi-Fi module for wireless monitoring and control
  • Control using PC software or APP

Technical specifications

  • Nominal battery voltage: 12V / 24V / 48V
  • Continuous power: 800W/1600W/2400W/4000W
  • Maximum power: 2000W/4000W/600W/10000W (short-term peak)

Datasheet English

Datasheet German

Manual English

Manual German

BUY NOW

Accessories
MT1 Display/Remote Control

The solar remote control with comfort display for the MPPT solar charge controller enables visual control of the charging parameters during operation and remote control of the MPPT solar charge controller.
The integrated real-time display enables an evaluation of the ampere hours.

Optional accessories for the EPIPDB series. The solar remote control with comfort display enables a visual check of the charging parameters during operation.
The integrated real-time display enables an evaluation of the ampere hours.

Characteristics

  • Easy handling
  • Display of the solar parameters
  • Selectable battery type
  • Display of the loading parameters
  • Control via four buttons
  • Remote control of the charge controller
  • incl. 2 meter cable

Manual English

Manual German

BUY NOW

MT11 Display/Remote Control

Display/remote control MT11

for EPSolar DuoRacer Series

  • Automatic recognition of type and model of the charge controllers
  • Real time display of operating data via LCD display
  • Three-button system for easy operation
  • Direct power supply through the charge controller
  • Setting the parameters, battery type and temperature
  • Real time display for error messages of the connected charge Controllers

The MT11 is compatible with the charge controllers of the DuoRacer series from EPSolar. It shows operating data and the working status of the charge controller in real time directly on the LCD display. The displayed parameters can also be set manually. Ideal for Camper, RV, boats etc.

 

Technical data

  • Supported models: DuoRacer series
  • Self consumption (AN): 12mA/5VDC
  • Self consumption (OFF): 4mA
  • Communication: RS485
  • Operating temperature: -20°C to +70°C
  • Enclosure: IP20
  • Dimensions: 98,4mm x 98,4mm
  • Weight: 0,11kg

Datasheet-German

Datasheet-English

BUY NOW

MT50 Display/Remote Control

The solar remote control with comfort display for the MPPT solar charge controller enables visual control of the charging parameters during operation and remote control of the MPPT solar charge controller.

Monitoring and remote control are possible thanks to the integrated real-time display.

Characteristics

  • Easy handling
  • Display of the solar parameters
  • Display of the loading parameters
  • Integrated real-time clock
  • Yield record
  • Remote control of the charge controller
  • incl. 2 meter cable

Remote display MT50 with display suitable for EPSolar charge controllers:

  • LS-B
  • VS-BN
  • XTRA
  • Tracer BN
  • Tracer AN
  • Tracer A

Datasheet English

Manual English

Manual German

BUY NOW

MT75 Display/Remote Control

Display/Remote Control MT75

for EPSolar charge controller and inverter

  • display and changing of operating parameters of charge controller and inverter simultaneously
  • display of error codes
  • direct control of load output by on/off button
  • remote control of inverter on/off
  • easy connection with EPSolar devices

MT75 is a new generation of remote control. It allows displaying and changing the operating parameters of charge controller and inverter at the same time, providing the ideal solution for various off-grid solar applications.

Compatible with:

  • Charge Controller
    • XTRA-N Series
    • Triron series
    • Tracer-AN series
    • Tracer-BN Series
    • iTracer Series
  • Inverter
    • IPower Series
    • IPower Plus Series
    • NPower Series
    • SHI Series

Technical data

  • LCD backlight: YES
  • Self consumption: 14mA/5V (without light), 26mA/5V (with light)
  • Operating temperature: -20°C to + 65°C
  • Storage temperature: -20°C to + 80°C
  • Dimensions: 193 x 94.6 x 48mm
  • Weight: 0.29kg

Datasheet-German

Datasheet-English

BUY NOW

eBox WiFi Adapter

The eBox-WIFI-01 adapter box enables wireless monitoring using WIFI communication between the solar controllers / inverters from EPSolar and the smartphone APP. Parameter setting, monitoring, etc. is conveniently possible via the APP interface.

Functions

  • Enables wireless monitoring monitoring of the solar controller / inverter
  • Support of the smartphone app by simple plug and play setting
  • High-performance CPU with M4 core
  • Ultra-low power consumption and the ability to process high-speed data
  • No external power supply necessary
  • Send and receive distance up to 50 meters
  • One-button reset to be able to reset to factory settings
  • Network cable included

Compatible with

  • LS-B
  • VS-BN
  • Tracer-A
  • Tracer BN
  • SHI
  • STI

The connection via WiFi works like any WiFi router. In its available WiFi networks, the Ebox appears as an open network with which you can then connect. Settings and monitoring only work using the EPSolar APP. With this APP you can monitor, set and read out your charge controller.

Datasheet 1 English

Datasheet 2 English

Manual English

BUY NOW

eBox Bluetooth Adapter

The eBox-BLE-01 adapter box enables wireless monitoring using Bluetooth communication between the solar controllers / inverters from EPSolar and the smartphone APP. Parameter setting, monitoring, etc. is conveniently possible via the APP interface.

Functions

  • Enables wireless monitoring monitoring of the solar controller / inverter
  • Support of the smartphone app by simple plug and play setting
  • High-performance Bluetooth chip with ultra-low power consumption
  • Supports Bluetooth 4.0 and BEl technology
  • Fast communication with strong anti-interference ability
  • No external power supply necessary
  • Transmission and reception distance up to 10 meters
  • Master reset adapter
  • Network cable included

Compatible with

  • LS-B
  • VS-BN
  • Tracer-A
  • Tracer BN
  • XTRA
  • SHI
  • STI

The connection via Bluetooth only works with the EPSolar APP.
This Android APP is free and is offered via an external server (not Playstore). With this APP you can monitor, set and read out your charge controller.

Datasheet 1 English

Datasheet 2 English

Manual English

BUY NOW

Temperature sensor RTS300

The temperature sensor is clamped to the charge controller and applied to the battery.
This way the sensor can provide the exact battery temperature to the charge controller.

Suitable for series:

Technical Details:

  • Length: 3 meters
  • Sensortype: RTS300R47K3.81A

BUY NOW

Temperature sensor RTS150

Temperature sensorcable for EPSolar charge controllers

Compatible with series

  • EPipDB
  • EPipC

The temperature sensor is connected to the charge controller and applied to the battery.
This allows the sensor to transmit the exact battery temperature to the charge Controller.

BUY NOW

Adapter cable RS485-USB for charge controllers and inverters

Adapter cable RS485-USB

to connect EPSolar charge Controllers and Inverters with PC

By using the monitoring software for the controller, it is possible to follow and record the solar power, battery voltage and load output graphically in real time and to change the parameters of the controller.
This allows the parameters of the Controller to be monitored in real time via PC.

Cable length: 90cm

Suitable for Series:

Not suitable for older controllers of the LS, MPPT-RN or VS-N versions

BUY NOW

Adapter cable CC-RJ45-3.81 for charge controllers

Adapter cable CC-RJ45 to connect EPSolar charge Controllers with remote/ebox

Suitable for Series

  • eTracer / iTracer
  • DuoRacer

By using the monitoring software for the controller, it is possible to follow and record the solar power, battery voltage and load output graphically in real time and to change the parameters of the controller.
This allows the parameters of the Controller to be monitored in real time via PC.

BUY NOW

Adapter cable RS485-USB-4LLT for charge controllers

Adapter cable RS485-USB-4LLT to connect EPSolar charge Controllers with PC

Suitable for Series

  • Tracer -BP
  • LS -BP

By using the monitoring software for the controller, it is possible to follow and record the solar power, battery voltage and load output graphically in real time and to change the parameters of the controller.
This allows the parameters of the Controller to be monitored in real time via PC.

Cable length: 1,5m

BUY NOW

Adapter cable RS485-RS485 for charge controllers and inverters

Adapter cable RS485-RS485 to connect EPSolar charge Controllers and Inverters with remote/ebox

Suitable for Series

  • Tracer -AN/-BN/-A
  • XTRA
  • GoMate
  • TRIRON
  • LS -B
  • VS -BN
  • SHI
  • STI
  • NP
  • IP -Plus

By using the monitoring software for the controller, it is possible to follow and record the solar power, battery voltage and load output graphically in real time and to change the parameters of the controller.
This allows the parameters of the Controller to be monitored in real time via PC.

BUY NOW

PAL-ADP-50AN Parallel Adapter

EPSolar PAL-ADP-50AN Tracer AN 50-100A Parallel Adapter

  • adjustment of the charging current of several devices connected in parallel
  • Real time monitoring and recording of the loading and operating status
  • Automatic charging and operation adjustment to the battery level
BUY NOW

EPSolar PAL-ADP-50AN Tracer AN 50-100A Parallel Adapter

Features

  • adjustment of the charging current of several devices connected in parallel
  • Real time recording of the loading and operating status
  • Automatic charging and operation adjustment to the battery level
  • Up to 6 charge controllers can be operated in parallel
  • Allows parallel operation of different models
  • Standard Modbus communication protocol
  • PC Monitoring Software
  • LED display for operating Status

Technical data

  • Supported models: Tracer AN 50-100A
  • Input voltage: 5VDC (provided by the charge controller)
  • operation consumption: 0,25W
  • Dimensions: 151,5mm x 69,9mm x 25,7mm
  • mounting dimension: 133,4mm
  • mounting holes size: 6,5mm
  • operating temperature: -33 to +55°C
  • Housing: IP30
  • Weight: 30g

Datasheet German

Datasheet English

Manual German

Manual English

Extension module RS485-1M2S for charge controllers and inverters

EPSolar Extension module RS485-1M2S for charge controllers/Inverters

Simple extension of the communication interface of EPSolar charge controllers/inverters.

  • Connection of eBox WiFi/BLE, PC and display/remote at the same time
  • Standard Modbus communication
  • Setting of baud rate via one button
  • LED Display

Technical data

  • Compatible devices: EPSolar charge controller/Inverter
  • Power supply: 5VDC (directly from charge controller/inverter)
  • Auxiliary power supply: 8-70VDC (from battery)
  • Self consumption: 0.3W
  • Baud rate: 115200 (standard), 9600
  • Operating temperature: -30°C to +50°C
  • Protection class: IP30
  • Dimensions (LxWxH): 121mm x 88mm x 27,5mm
  • Weight: 121.8g

Manual-English

Manual-German

BUY NOW

Charge Controller
Triron Series (10-40A)
Charge Controller EPSolar MPPT Triron Series 10-40A Highly efficient and compact MPPT charge controller for self configuration! Selection of 3 different display modules Selection of 3 differe... Read More
XTRA Series
The XTRA-N series can display different display units (XDB1 / XDS1 / XDS2). The series includes a water-repellent housing (design) with protection class IP32. With the new XTRA-N series, the reliability of the devices has be... Read More
GoMate Series
The GoMate series combines design with technology and is an eye-catcher among solar charge controllers. The fully integrable solar charge controllers were specially developed for an aesthetically unobtrusive installation. They wor... Read More
Tracer AN Series (50-100A)
Tracer AN Series MPPT Solar Charge Controller Very large range of application from caravans, single family houses to large installations. MPPT charge controller 60A/80A/100A 12-48V system vol... Read More
UPower Series
Inverter / charge controller UPower series from EPSolar for PV / solar applications. Suitable for solar, car, boat, camping, outdoor, caravan, motorhome etc. Ideal for use in remote areas with many hours of sunshine and with a lack of re... Read More
DuoRacer Series(10-30A)
Charge controller EPSolar MPPT DuoRacer 10-30A Highly efficient, compact and reliable charge controller to use the full power of your solar modules The MPPT charge controller DuoRacer from EPSolar was speci... Read More
Tracer BN Series (10-40A)
Charge Controller EPsolar MPPT Tracer BN-Series 10-40A 12-24V Characteristics MPPT (Max Power Point Tracking) Maximum charge current 10-40A Automatic system voltage ... Read More
iTracer Series
The charge controllers of the iTracer series are industrial goods with an extended Maximum Power Point Tracking (MPPT) algorithm. You can supply the maximum available power for charging batteries. Properties ... Read More
VS AU Series
The VS series is a generation of charge controllers for off-grid solar systems, such as street lighting, solar home systems or small power plants, etc. It combines an LCD display, reliable battery charging, fully electronic protection, p... Read More
VS BN Series
The devices of the VS BN series can charge and discharge a battery automatically, especially with off-grid PV systems. The current operating state is determined by a hybrid actuator and, as a result, the charging process is optimi... Read More
EP Series
The EP series is a double battery charging control for caravans, campers, boats and golf carts etc. The charging priority can be selected. Solar charge controller with system voltages from 12V to 24Volt for 2 different batteries w... Read More
Tracer AN Series (10-40A)
Charge Controller EPSolar MPPT Tracer AN Series 10-40A Characteristics MSRT (Multiphase synchronous rectifier technology) Advanced MPPT logarithms with dual-core processor Ar... Read More
LS1024EPD 12-24V 10A
Charge Controller EPSolar PWM LS1024EPD 10A 12/24V 12/24 VDC Day / Night recognition LED Indicator for battery status Electronic protection Intelligent timer function (1-... Read More
LS EU Series
 Charge controller EPSolar PWM LS-EU Series   The LS-EU solar charge controller is a new member of the LandStar family and is ideal for small solar installations, especially household systems. ... Read More
Inverter
IPower Plus Series
Sine wave inverter EPSolar IPower Plus series 1500-3000W 12-48V For use in solar applications, car, boat, camping, outdoor, caravan, motorhome etc.   Nominal voltage battery: 12V / 24V / 4... Read More
SHI Series
The SHI series sine wave inverters convert 12 / 24V direct current fully digital into 220 / 230V 50 / 60Hz alternating current. The SHI series is characterized by high reliability, high efficiency, compact size, easy installation and ope... Read More
STI Series
The STI series sine wave inverters are fully digital and impress with their intelligent design. DC 12V / 24V / 48V to 220V AC / 50Hz, high performance DSP Properties high reliability high eff... Read More
Inverter Charger
UPower Series
Inverter / charge controller UPower series from EPSolar for PV / solar applications. Suitable for solar, car, boat, camping, outdoor, caravan, motorhome etc. Ideal for use in remote areas with many hours of sunshine and with a lack of re... Read More
Accessories
MT1 Display/Remote Control
The solar remote control with comfort display for the MPPT solar charge controller enables visual control of the charging parameters during operation and remote control of the MPPT solar charge controller. The integrated real-time ... Read More
MT11 Display/Remote Control
Display/remote control MT11 for EPSolar DuoRacer Series Automatic recognition of type and model of the charge controllers Real time display of operating data via LCD display Three-b... Read More
MT50 Display/Remote Control
The solar remote control with comfort display for the MPPT solar charge controller enables visual control of the charging parameters during operation and remote control of the MPPT solar charge controller. Monitoring and remote co... Read More
MT75 Display/Remote Control
Display/Remote Control MT75 for EPSolar charge controller and inverter display and changing of operating parameters of charge controller and inverter simultaneously display of error codes... Read More
eBox WiFi Adapter
The eBox-WIFI-01 adapter box enables wireless monitoring using WIFI communication between the solar controllers / inverters from EPSolar and the smartphone APP. Parameter setting, monitoring, etc. is conveniently possible via the APP int... Read More
eBox Bluetooth Adapter
The eBox-BLE-01 adapter box enables wireless monitoring using Bluetooth communication between the solar controllers / inverters from EPSolar and the smartphone APP. Parameter setting, monitoring, etc. is conveniently possible via the APP... Read More
Temperature sensor RTS300
The temperature sensor is clamped to the charge controller and applied to the battery. This way the sensor can provide the exact battery temperature to the charge controller. Suitable for series: ... Read More
Temperature sensor RTS150
Temperature sensorcable for EPSolar charge controllers Compatible with series EPipDB EPipC The temperature sensor is connected to the charge controller and applied to the batte... Read More
Adapter cable RS485-USB for charge controllers and inverters
Adapter cable RS485-USB to connect EPSolar charge Controllers and Inverters with PC By using the monitoring software for the controller, it is possible to follow and record the solar power, battery voltage... Read More
Adapter cable CC-RJ45-3.81 for charge controllers
Adapter cable CC-RJ45 to connect EPSolar charge Controllers with remote/ebox Suitable for Series eTracer / iTracer DuoRacer By using the monitoring software for the controller... Read More
Adapter cable RS485-USB-4LLT for charge controllers
Adapter cable RS485-USB-4LLT to connect EPSolar charge Controllers with PC Suitable for Series Tracer -BP LS -BP By using the monitoring software for the controller, it is pos... Read More
Adapter cable RS485-RS485 for charge controllers and inverters
Adapter cable RS485-RS485 to connect EPSolar charge Controllers and Inverters with remote/ebox Suitable for Series Tracer -AN/-BN/-A XTRA GoMate TRIRON LS -B... Read More
PAL-ADP-50AN Parallel Adapter
EPSolar PAL-ADP-50AN Tracer AN 50-100A Parallel Adapter adjustment of the charging current of several devices connected in parallel Real time monitoring and recording of the loading and operating st... Read More
Extension module RS485-1M2S for charge controllers and inverters
EPSolar Extension module RS485-1M2S for charge controllers/Inverters Simple extension of the communication interface of EPSolar charge controllers/inverters. Connection of eBox WiFi/BLE, PC and displa... Read More